Pneumatic Swing Clamps
Standard Features
- Arms swing 90°.
- Our capscrew arm design is available. You may modify our arm, or we have provided you with dimensions to make your own.
- Special wipers and swept-line cylinder tops help keep chips from packing and coolant contaminants from entering the swing clamp.
- Swing clamp bodies are wrought aluminum alloy with PHC™ (Pneumatic Hardcoat) coating on all external and internal surfaces. This gives the clamps extended life.
- Plungers are carbon steel with hard chrome plating. The guide bushings are hardened alloy steel.
- All dynamic seals are internally lubricated and made from a specially compounded elastomer to promote smooth break away and low operational drag.
- Six bore sizes are available in two mounting styles to best adapt to your application.
- All models are available in straight pull and left or right swings.
- Magnetic pistons are standard on all models, allowing you to use position indicating sensors.
- Position sensors mount within the clamp's space envelope so sensor usage doesn't encroach on the clamp's mounting envelope.
- Position sensors have an LED indicator to reduce set-up time.
- All swing clamps have internal orifices to prevent cam damage caused from over accelerating the clamp.
- VektorAir™ clamps are double acting to reduce mounting envelope and prevent non-return and slow return problems inherent with single acting clamps.
- To determine whether a straight pull, left or right swing should be specified, imagine viewing the arm from above during the clamping stroke. Arms moving clockwise are right hand swings, counter-clockwise are left hand swings.
|
|
Top Flange Threaded Body Pneumatic Swing Clamps
Specifications
|
|
Double Acting (D/A) Cylinders actuated pneumatically both directions
Clamp supplied with a standard arm.
|
*See graphs for clamp curves and extended arm performance force. It is recommended that the clamp position be set at about 50% of the clamp stroke. These devices should be positioned in no less than ½ second. These recommendations apply when using the standard arm. When using the extended or large custom arms, allow one second for positioning.
** Per complete cycle
Dimensions
Standard Arm is supplied with clamp.
* Per complete cycle
** See graphs for clamp curves and extended arm performance. It is recommended that the clamp position be set at about 50% of the clamp stroke. These devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard arm. When using extended arms or large custom arms, allow 1 second for positioning.
ounting Brackets
| P6-4031-20 | P6-4031-60 | P6-4031-80 | P6-4032-30 | P6-4032-70 | P6-4033-20 |
A |
1 1/4 - 16 |
1 5/8 - 16 |
1 7/8 - 16 |
2 5/16 - 16 |
2 3/4 - 16 |
3 1/4 - 16 |
B |
2.13 |
2.50 |
3.38 |
3.25 |
3.75 |
4.25 |
C |
1.06 |
1.25 |
1.69 |
1.63 |
1.88 |
2.13 |
D |
.81 |
1.00 |
1.28 |
1.38 |
1.63 |
1.81 |
E |
1.63 |
2.00 |
2.56 |
2.75 |
3.25 |
3.63 |
F |
.88 |
1.13 |
1.25 |
1.50 |
1.75 |
2.00 |
G |
1.75 |
2.25 |
2.50 |
3.00 |
3.44 |
4.00 |
H |
.56 |
.50 |
1.00 |
.63 |
.75 |
.75 |
J |
.28 |
.25 |
.62 |
.31 |
.31 |
.31 |
K |
.28 |
.28 |
.53 |
.28 |
.28 |
.28 |
L |
.12 |
.09 |
.25 |
.62 |
.84 |
1.40 |
M |
1.50 |
1.75 |
2.50 |
2.00 |
2.25 |
2.25 |
|
Specifications
|
|
Double Acting (D/A) Cylinders actuated pneumatically both directions
Clamp supplied with a standard arm |
*See graphs for clamp curves and extended arm performance force. It is recommended that the clamp position be set at about 50% of the clamp stroke. These devices should be positioned in no less than ½ second. These recommendations apply when using the standard arm. When using the extended or large custom arms, allow one second for positioning.
** Per complete cycle
Pneumatic Link Clamp Specifications
|
Operating Pressure Range: 30 - 250 psi
Fluid: Clean Dry Air
Lubrication: Not Required
* Equal to ±3° with standard lever.
** Use of extended length arms will result in a reduction of clamp capacity. See graphs of lever output curves for clamping force of various arm lengths. The clamping force is adjustable by varying the pneumatic system pressure. To insure maximum service life and trouble-free operation, these devices should be positioned in no less than ½ second. These recommendations apply when using the standard arm. When using the optional long arm or your custom arm, please restrict the flow rates to position the arm in no less than 1 second.
*** Per complete cycle.
|
Pneumatic Link Clamps
Double Acting
- Excellent alternative to swing clamps when swing space is limited
- Available in three sizes: 1, 1-1/2, and 2-1/8 inch bore
- Top Flange body mount
- Left, forward, or right lever position from the same body
- Link clamps clear large obstructions better than other types of clamps
- Manifold mounted or standard plumbed using standard NPT fittings
- Levers sold seperately
|
Shown with Extended Length Levers.
|
Dimensions
|
Levers are to be adjusted to within ±3° of nominal clamp angle to prevent premature failure.
|
Mounting Port / Manifold Dimensions
Model No | 91-6011-03 | 91-6015-03 | 91-6021-03 |
Cyl Bore Dia |
1.00 |
1.50 |
2.125 |
A |
1.88 |
2.63 |
3.09 |
B |
.75 |
1.00 |
1.25 |
C |
.50 |
.75 |
.88 |
D |
.2515 |
.3765 |
.5015 |
E |
.19 |
.31 |
.38 |
F |
.19 |
.31 |
.38 |
G |
.2505 |
.3755 |
.5005 |
H |
.75 |
1.00 |
1.19 |
J |
.13 |
.31 |
.38 |
K |
.50 |
.75 |
.94 |
L |
.50 |
.69 |
.88 |
M |
.25 |
.38 |
.44 |
N |
.26 |
.39 |
.45 |
P |
1.69 |
2.25 |
2.69 |
Q |
1/4-20 UNC |
3/8-16 UNC |
1/2-13 UNC |
R |
1.25 |
2.25 |
3.00 |
S |
.19 |
.28 |
.38 |
Model No | 91-6011-02 | 91-6015-02 | 91-6021-02 |
Cyl Bore Dia |
1.00 |
1.50 |
2.125 |
A |
3.00 |
3.50 |
4.00 |
B |
.75 |
1.00 |
1.25 |
C |
.50 |
.75 |
.88 |
D |
.2515 |
.3765 |
.5015 |
E |
.19 |
.31 |
.38 |
F |
.19 |
.31 |
.38 |
G |
.2505 |
.3755 |
.5005 |
H |
.75 |
1.00 |
1.19 |
J |
.13 |
.31 |
.38 |
K |
.50 |
.75 |
.94 |
L |
.50 |
.69 |
.88 |
N |
.26 |
.39 |
.45 |
Dual Path Rotary Union
Dimensions
Operating Parameters
- Max Pressure: 200 psig
- Max Rotational Speed: up to 100 RPM
|
|
|
P1-5040-00 P1-5046-00 P1-5070-00 P1-5076-00 P1-5110-00 P1-5116-00 P1-5140-00 P1-5146-00 P1-5200-00 P1-5206-00 P1-5240-00 P1-5246-00 P1-5208-00 P6-4001-80 P6-4002-30 P6-4001-20 P6-4001-60 P6-4002-70 P6-4003-20 P1-5048-00 P1-5078-00 P1-5118-00 P1-5148-00 P1-5248-00 P6-4031-20 P6-4031-60 P6-4031-80 P6-4032-30 P6-4032-70 P6-4033-20 P6-4011-20 P6-4011-60 P6-4011-80 P6-4012-30 P6-4012-70 P6-4013-20
P1-5071-00 P1-5077-00 P1-5041-00 P1-5047-00 P1-5117-00 P1-5141-00 P1-5147-00 P1-5201-00 P1-5207-00 P1-5241-00 P1-5247-00 P1-5111-00 P1-5049-00 P1-5079-00 P1-5119-00 P1-5149-00 P1-5209-00 P1-5249-00
P6-2297-00 P6-2297-01
91-5009-03 91-5005-03 91-5015-03 91-5025-03
91-6011-02 91-6015-02 91-6021-02 91-6015-03 91-6021-03 91-6011-03 P1-6621-10 P1-6621-11 P1-6621-12 P1-6621-50 P1-6621-51 P1-6621-52 P1-6622-10 P1-6622-11 P1-6622-12
P1-5005-00 P1-5005-01
P3-2242-01-ES-6A P3-2242-01-ES12A P3-2242-01
P3-2442-01 P3-2442-01-ES12A P3-2442-01-ES6A
P3-0015-00 P3-0015-01 P3-0015-02 P3-0220-01 P3-0122-00 P3-0222-00 P3-0132-00 P3-0232-00 P3-0332-00 P7-0010-01 P3-0016-00 P3-0026-00 P3-0036-00 P3-0120-00 P3-0230-00 P3-0112-01 P3-0122-01 P3-0232-01 P3-0332-01 P7-0020-00 P7-0020-01 P3-0022-00 P3-0032-00 P3-0121-00 P3-0221-00 P3-0321-00 P3-0231-00 P3-0218-00 P3-0128-00 P3-0228-00 P3-0328-00 P3-0238-00 P3-0021-01 P3-0031-01 P3-0128-01 P3-0238-01 P3-0218-01 P3-0148-00 P3-0248-00 P3-0141-00 P3-0241-00 P3-0015-03 P3-0128-02 P3-0131-00 P3-0015-04 P3-0015-05 P3-0138-01 P5-0044-00 P5-0303-00
P7-1030-00 P7-1021-01 P7-1021-00
P7-1030-01 P7-1011-00 P7-1012-00
P7-0030-00 P7-0030-01
P3-1012-00 P3-1002-00 P3-1013-00
P9-1710 P9-1728 P9-1736 P9-2015 P9-2023 P9-2031 P9-2049 P3-0015-04 P3-0015-05
P9-2205 P9-2213 P9-2221 P9-2262 P9-2270 P9-2288
P9-1710 P9-1728 P9-1736 P9-2015 P9-2023 P9-2031 P9-2049 P3-0015-04 P3-0015-05
P9-2205 P9-2213 P9-2221 P9-2262 P9-2270 P9-2288
P9-5034 P9-5059
|